Part of our Building Your First Ham Radio Station guide.

Before you buy wire or a vertical, three decisions shape how well the antenna will work in your yard: where you feed it, how high you hang it, and, if it’s a vertical, whether it lives on the roof or the ground. None of them has one right answer. Each one depends on your supports, your space and what kind of contacts you actually want to make.

Jump to: Center-fed vs end-fed · Antenna height · Roof vs ground verticals

Center-Fed vs End-Fed: Choosing Your Feed Point

Where you feed a wire antenna, at the center or at one end, changes more than how you hang the wire. It affects impedance, installation flexibility, and how forgiving the antenna is about your particular yard.

Center-fed dipole and end-fed half-wave compared by supports, impedance, matching, counterpoise, and best use

Center-fed: the classic dipole

A center-fed dipole splits into two equal legs from a feed point in the middle and presents an impedance close to 50 ohms at resonance, which is why it pairs so easily with coax and a simple 1:1 balun. The tradeoff is installation: you need support at the center and at both ends, which means two support points plus a way to get coax to the middle, or one high center support with the legs sloping down as an inverted vee.

End-fed: one support point, higher impedance

An end-fed half-wave is fed from one end, where the impedance is much higher, typically thousands of ohms, so it needs a 49:1 or similar transformer to bring it down to something coax can handle. The big advantage is installation: one high support point, with the feed point near the ground where your radio sits. That’s why it’s a favorite for POTA activators who want to throw one line over one tree.

End-fed antennas generally benefit from a counterpoise wire at the feed point to complete the RF circuit and reduce common-mode current on the coax shield. Skipping it is a common reason an EFHW underperforms or puts RF in the shack. A center-fed dipole doesn’t have the same requirement, since its two symmetric legs do that job. More on that in Why an EFHW Benefits From a Counterpoise.

Center-fed dipoleEnd-fed half-wave
SupportsCenter and both ends, or one center support for an inverted veeOne high point
Feed point impedanceNear 50 ohms at resonanceThousands of ohms
Matching1:1 balun49:1 transformer
CounterpoiseNot neededUsually helps
Best forFixed stations with roomPOTA and quick setups
  • One tall support and a radio position near the ground: end-fed half-wave.
  • Two supports, or one center support for an inverted vee: center-fed dipole.
  • The cleanest impedance match with the least transformer complexity: center-fed dipole.
  • Portability and single-point setup speed matter most: end-fed half-wave.

Neither feed point is objectively better. They solve different installation problems. For the two end-fed designs head to head, including 1:1, 4:1, 9:1 and 49:1 transformers, see EFHW vs Random Wire. If you want one antenna to cover many bands no matter where it’s fed, see ladder line and open-wire feedline.

Antenna Height: How Much Does It Actually Matter?

Every ham has heard “get it up in the air,” and it’s generally true. But the relationship between height and performance is more nuanced than higher equals better, especially once you factor in what you’re actually trying to work.

Half-wavelength antenna heights for 80, 40, 20, 15, and 10 meters

Height changes your radiation angle

A horizontal antenna’s radiation angle, the vertical angle at which most of its energy leaves, depends on its height above ground measured in wavelengths, not feet. A dipole that’s low relative to a wavelength radiates most of its energy nearly straight up, which is exactly what you want for regional NVIS contacts and nearly useless for DX. Raise the same dipole toward a half wavelength or more and its radiation shifts to lower angles that travel farther before reflecting off the ionosphere.

That’s why wavelength, not feet, is what matters. A dipole at 30 feet is high on 10 meters and low on 80 meters, so the same antenna can favor DX on the high bands while still doing useful NVIS-style regional work on the low ones.

Height also lowers your noise floor

Getting an antenna higher and farther from your house, power lines and other noise sources lowers your noise floor, so you hear weak signals you’d otherwise miss. That helps no matter what you’re trying to work, and it’s one of the most underrated reasons to prioritize height when you can.

BandHalf wavelengthQuarter wavelength
80 mabout 135 ftabout 68 ft
40 mabout 69 ftabout 34 ft
20 mabout 35 ftabout 17 ft
15 mabout 23 ftabout 12 ft
10 mabout 17 ftabout 9 ft

These are rough targets for a horizontal dipole. Near a half wavelength up, the antenna starts favoring the low angles DX arrives on. Below about a quarter wavelength, most of the energy goes nearly straight up, which is where NVIS works best.

So how high should you go?

  • Regional nets and NVIS on 40 and 80 meters: keep it relatively low. 20 to 35 feet often works well.
  • DX: as high as your situation reasonably allows, ideally approaching a half wavelength or more on your main bands.
  • Not sure which matters more: 30 to 40 feet is a reasonable compromise on most HF bands.

The right height depends on the contacts you want, not the biggest number your yard or budget allows. For more on that tradeoff, see NVIS vs. Vertical DX Antennas.

Roof-Mounted vs Ground-Mounted Verticals

Mounting a vertical on a roof instead of at ground level solves some real problems and creates a few new ones that don’t show up until you’re up there installing it.

Ground-mounted and roof-mounted vertical antennas compared by radials, height, access, lightning, and coax

Small lots, HOA restrictions on ground-level structures, or simply wanting the antenna higher and away from clutter all push hams toward the roof. Getting a vertical up and away from nearby obstructions can improve performance, and it keeps the antenna away from kids, pets and neighbors.

The radial system problem

Ground-mounted verticals rely on radials laid on or buried in the earth (see How Ground Radials Impact Your Vertical Antenna). A roof-mounted vertical can’t use ground radials in any practical sense, so it needs elevated radials: wires running horizontally or drooping from the base of the antenna. Elevated radials work well, but they use fewer of them, typically two to four per band, each cut to a resonant quarter wavelength, instead of the many-radial approach used at ground level. Getting this wrong is one of the most common reasons a roof-mounted vertical underperforms.

Structural and practical concerns

  • Wind load on a roof mount goes straight into your roof structure, so a taller or heavier vertical needs real mounting hardware, not an improvised bracket.
  • Lightning protection matters more, since a roof-mounted antenna is often the highest point on the house.
  • Coax runs get longer and often have to penetrate the roof or run along the outside, and both need careful weatherproofing.
  • Every adjustment or repair means getting back up on the roof.

Grounding and code

A roof-mounted antenna mast should be bonded to your home’s electrical service ground, and the National Electrical Code (Article 810) covers how antenna masts and lead-in conductors are grounded. Add a coax lightning arrestor where the feedline enters the building, bonded to that same ground. If you’re not sure what your local code requires, a licensed electrician can confirm it. My full write-up is Station Grounding and Lightning Protection.

Is it worth it?

If ground mounting isn’t an option because of space or restrictions, a properly executed roof mount with a real elevated radial system can perform very well. The key words are properly executed. Half-measures on radials or mounting hardware are where roof-mounted verticals earn their reputation for underperforming.

Related reading: Multiband Wire Antennas · Stealth Antennas for HOA Neighborhoods · Tower and Mast Permitting


0 0 votes
Article Rating
Subscribe
Notify of
guest

0 Comments
Oldest
Newest Most Voted
0
Would love your thoughts, please comment.x
()
x
×